E5 series cartridges are composed of advanced polypropylene membrane and supporting layer, with high flux, high precision and low pressure drop, it is an economical choice for pre-filtration.
Applications
? Buffer prefiltration
? Pre-filtration of sterile raw materials
? Pre-filtration of water for pharmaceutical use
? Blood product prefiltration
Product features
? No fiber shedding
? Gradient pore size with extremely high dirt holding capacity
? No foreign substances such as adhesives
? Features broad chemical resistance
Flow curves
MoC | |
Membrane material | Polypropylene |
Center rod/housing/end cap | Polypropylene |
Supporting layer | Polypropylene |
Sealing ring | Refer to ordering information |
Surface area | 0.4m2/10 inch |
Working condition | |
Max. working temperature | 80℃(0.173MPa) |
Max. working pressure difference | 0.5MPa（25℃） |
0.25MPa（80℃） | |
Autoclave | 121℃ (30min,5 times) |
Biosafety | |
Endotoxin | ＜0.25EU/ml |
Biosafety | Meets USP<87> and USP<88> biosafety requirements |
Product number key of high precision polypropylene disc filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Inlet/Outlet | Sterilization |
DS=Disc filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 02=2 | 2H=1/4" HB | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Product number key of high precision polypropylene CA series capsule filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Structure type | Inlet | Outlet | Sealing ring material | Sterilization |
CA=Diameter 110 capsule filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 05=5 10=10 20=20 30=30 | L=Up-in & down-out | H=1"-1.5" TC | H=1"-1.5" TC F=1/2" HB | S=Silicone E=EPDM V=Fluorelastomer | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Technical parameter of high precision polypropylene CA series capsule filter
Material | Series | Size code | Single/dual layer | Surface area（㎡）≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | CA capsule filter | F05 | Single layer | 0.2 | ≥5L/min |
F10 | Single layer | 0.4 | ≥10L/min | ||
F20 | Single layer | 0.8 | ≥20L/min | ||
F30 | Single layer | 1.2 | ≥30L/min |
Product number key of high precision polypropylene CB series capsule filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Structure type | Inlet | Outlet | Sterilization |
CB=Diameter 70 capsule filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F= Pharmaceutical grade | H1=1(minor Dia.) 01=1(wide Dia.) 1H=1.5 02=2.5 05=5 | L=Up-in & down-out | A=1/4"NPT D=1/4" HB E=3/8" HB F=1/2" HB G=1/2" TC H=1-1.5" TC J=1/4-1/2" HB | A=1/4"NPT D=1/4" HB E=3/8" HB F=1/2" HB G=1/2" TC H=1-1.5" TC J=1/4-1/2" HB | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Technical parameter of high precision polypropylene CB series capsule filter
Material | Series | Size code | Single/dual layer | Surface area（㎡）≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | CB capsule filter | FH1 | Single layer | 0.01 | ≥0.25L/min |
F01 | Single layer | 0.02 | ≥0.5L/min | ||
F1H | Single layer | 0.04 | ≥1L/min | ||
F02 | Single layer | 0.08 | ≥2L/min | ||
F05 | Single layer | 0.15 | ≥3.75L/min |
Product number key of high precision polypropylene cartridge
Membrane material | Pore size (μm) | Type | Length (inch) | Connection type | Sealing type | Sealing ring material |
E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 05=5 10=10 20=20 30=30 40=40 | A=226 B=226 steel liner D=222 E=222 steel liner H=215 K=220 | P=Flat cap R="8" shape tail K=220 | S=Silicone E=EPDM V=Fluorelastomer |
Technical parameter of high precision polypropylene cartridge
Material | Series | Size code | Single/dual layer | Surface area (㎡)≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | Cartridge | F05 | Single layer | 0.2 | ≥5L/min |
F10 | Single layer | 0.4 | ≥10L/min | ||
F20 | Single layer | 0.8 | ≥20L/min | ||
F30 | Single layer | 1.2 | ≥30L/min | ||
F40 | Single layer | 1.6 | ≥40L/min |
Copyright ? Shanghai Duoning Biotechnology Co., Ltd. All Rights Reserved Sitemap | Technical Support: 
Message-
